Diagnostic indicator 1、诊断指示器 2、诊断指征readout that flashes at one-second intervals. During normal operation, the readoutshows the node address of the scanner. During abnormal operation, it shows adiagnostic code. The following table describes how to interpret the informationdisplayed on this readout.扫描仪，诊断指标是一个2位LED发光二极管闪烁以1/2秒为间隔的读数。在正常操作期间，读数显示扫描仪的节点地址。在正常操作期间，它会显示一个诊断代码。下表介绍了如何解释这个读数上显示的信息。代码描述Code Description建议的纠正措施是确保把证书正确地导入Suggested Action:00 to 63: 正常运行。 所显示的数目就是在DeviceNet网络扫描仪的节点地址 Normal operation. The number shown isthe node address of the scanner on theDeviceNet network.无故障None.70：扫描失败的重复的节点地址检查。您选择的节点地址为该频道已经由网络上的另一个设备使用。这个频道的节点地址更改为当前未被使用的一个。 The scanner failed the duplicate nodeChange the node address of this channel toaddress check. The node address youone that is not currently being used.selected for this channel is alreadybeing used by another device on thenetwork.71:非法扫描列表中的数据。 交替出现问题的设备的节点地址与此诊断代码置扫描列表中删除任何非法的数据 Illegal data in the scanlist. TheReconfigure the scanlist to remove anynode address of the offending deviceillegal data.appears alternately with thisdiagnostic code.72:一个设备停止与扫描仪沟通。与此诊断代码有问题的设备的节点地址交替闪烁检查有问题的设备并验证该网络连接是安全的 A device stopped communicating withInspect the offending device and verify thatthe scanner. The node address of thethe network connection is secure.offending device flashes alternatelywith this diagnostic code.73:设备的标识识别扫描列表中的条目不匹配。与此诊断代码有问题的设备的节点地址交替闪烁The identification of a device doesnot match the identification entry inthe scanlist.The node address of theoffending device flashes alternatelywith this diagnostic code.74:此端口上的一个数据溢出发生A data overrun occurred on this port75:没有方括号是活跃在扫描仪。No scanlist is active in the scanner.76:未检测到扫描仪的直接网络通信No direct network traffic for thescanner was detected.77:数据大小返回到扫描仪扫描列表中的条目不匹配。与此诊断代码有问题的设备的节点地址交替闪烁。The data size returned to the scannerdoes not match the entry in thescanlist.The node address of theoffending device flashes alternatelywith this diagnostic code.78:方括号中列出的设备在网络上不存在。与此诊断代码有问题的设备的节点地址交替闪烁。A device listed in the scanlist doesnot exist on the network.The nodeaddress of the offending deviceflashes alternately with thisdiagnostic code.79:扫描仪未能传递信息。The scanner has failed to transmit amessage.更改设备识别扫描列表中的条目，以便符合实际的设备标识Change the device identification entry inthe scanlist so that it agrees with theactual device identification修改您的配置和检查无效数据。Modify your configuration and check forinvalid data.输入方括号。Enter a scanlist.没有人。 扫描仪听到其他网络通信None. The scanner hears other networkcommunication重新配置扫描仪和更改处理。Reconfigure the scanner and change theaddressing.添加设备到网络，或从扫描列表中删除该设备的条目。Add the device to the network, or delete theentry for that device from the scanlist.确保扫描仪连接到一个有效的网络。检查电缆断开。Make sure that the scanner is connected to avalid network.Check for disconnected cables.将PLC或SLC处理器在运行模式下。 把扫描仪放在通过模块状态寄存器的运行模式。Put the PLC or SLC processor in RUN mode.Put the scanner in RUN mode through ModuleStatus register.将PLC或SLC处理器在运行模式；检查阶梯程序对位错的原因Put the PLC or SLC processor in RUN mode;Check the ladder program for the cause ofthe fault bits80:PLC或SLC处理器是在PROG模式，或者从命令注册扫描仪在空闲模式。The PLC or SLC processor is in PROGmode; or, the scanner is in IDLE modefrom the Command register.81:PLC或SLC处理器是在PROG模式；或者，扫描仪是在从命令寄存器的故障模式。The PLC or SLC processor is in PROGmode; or, the scanner is in FAULT modefrom the Command register.82:从设备分散的IO消息序列中检测到错误。节点的地址与此诊断代码有问题的设备交替闪烁.Error detected in sequence offragmented IO messages from device.Thenode address of the offending deviceflashes alternately with thisdiagnostic code..83:当扫描仪试图与它沟通时，设备返回错误响应。与此诊断代码有问题的设备的节点地址交替闪烁A device is returningerror responses when the scannerattempts to communicate with it.Thenode address of the offending deviceflashes alternately with thisdiagnostic code.检查有问题的设备的条目在方括号来验证输入和输出数据的大小是正确的。检查有问题的设备的配置。Check the entry for the offending device inthe scanlist to verify that the sizes of theinput and output data are correct.Check theconfiguration of the offending device.检查扫描列表，验证是否列出了有问题的设备。检查有问题的设备的配置。Check the scanlist to verify that theoffending device is listed.Check theconfiguration of the offending device.没有人。 此代码清除本身一旦扫描仪试图初始化84:扫描仪是在DeviceNet通道初始化的过程通道上的所有设备。。None. This code clears itself once theThe scanner is in the process ofscanner attempts to initialize all of theinitializing the DeviceNet channels.devices on the channels.检查该扫描列表中的条目的准确性。 检查有问题的设备的配置。85:扫描器返回的数据大小大于预期Check accuracy of the entry in the scanlist.The data size returned to the scannerCheck the configuration of the offendingwas larger than expecteddevice86:设备是生产空闲状态数据扫描程序处于检查有问题的设备的配置。运行模式时。A device is producing idle-state dataCheck the configuration of the offendingwhile the scanner is in RUN mode.device87:浏览分配。 扫描仪尚未发现由分配给主机，或奴隶模式已启用，但扫描仪没有分配给主Available for allocation. The scannerhas not yet been detected by theallocated master, or slave mode is88：这是不是一个错误。 在启动和重置，扫描仪显示这一指标的所有阶层。This is not an error. At power-up andreset, the scanner displays allsegments of this indicator.90：您已经禁用了一个通信端口。You have disabled a communicationport.91：通信端口上检测到总线断开状态。扫描仪检测到通信错误。Bus-off condition detected on acommunication port.The scanner isdetecting communication errors.如果此诊断代码清除，监视扫描仪，以确定在硕士期间检测到扫描仪。如果代码仍然存在，请检查扫描仪的奴隶模式配置。Monitor the scanner to determine if thisdiagnostic code clears when a master detectsthe scanner.If the code remains, check theNone.没有重新配置扫描仪。Reconfigure the scanner.检查设备网连接和物理媒体的完整性。检查系统失败从设备或其他可能的网络干扰的来源。Check DeviceNet connections and physicalmedia integrity.Check system for failedslave devices or other possible sources ofnetwork interference.92：通信端口上检测到网络的力量。No network power detected oncommunication port.向网络提供电力。 确保电缆提供电源下降到扫描仪的通信端口。Provide power to the network. Make sure thatthe drop cable is providing power to thescanner’s communication port.没有人。 请勿断开扫描仪在一个FLASH更新过程；否则，扫描仪的内存中的数据将丢失。None. Do not disconnect the scanner while aFLASH update is in progress; otherwise, youwill lose the data in the scanner’s memory.None.没有人扫描仪或更换服务。Service or replace the scanner.扫描仪或更换服务。Service or replace the scanner.扫描仪或更换服务。Service or replace the scanner.95：一个闪存更新正在进行中的应用。An application FLASH update is inprogress.97：扫描仪是由用户停止命令。The scanner was halted by a user98：不可恢复的固件故障。Unrecoverable firmware failure.99：不可恢复的硬件故障。Unrecoverable hardware failure.E2：内存测试失败RAM test failureE4：内存测试failureLost(失败）电源在闪扫描仪或更换服务。存升级。Service or replace the scanner.RAM test failureLost power duringFLASH upgrade.扫描仪或更换服务。E5：failureLostNo或主引导代码。Service or replace the scanner.failureLostNo boot or main code.E9：fluorescentThe非易失性配置已损坏fluorescentThe non-volatileconfiguration is corrupt扫描仪的电源周期。 配置下载到扫描器.。Cycle power to the scanner. Download theconfiguration to the scanner..
